中心组合设计制备高比表面铝基核桃果皮多孔碳材料

刘晓红; 李甜甜; 孙悦晨; 张凡

doi:10.12030/j.cjee.201711177

环境工程学报

中心组合设计制备高比表面铝基核桃果皮多孔碳材料

, , ,

刘晓红, 李甜甜, 孙悦晨, 张凡. 中心组合设计制备高比表面铝基核桃果皮多孔碳材料[J]. 环境工程学报, 2018, 12(6): 1819-1824. doi: 10.12030/j.cjee.201711177

引用本文:

刘晓红, 李甜甜, 孙悦晨, 张凡. 中心组合设计制备高比表面铝基核桃果皮多孔碳材料[J]. 环境工程学报, 2018, 12(6): 1819-1824. doi: 10.12030/j.cjee.201711177

LIU Xiaohong, LI Tiantian, SUN Yuechen, ZHANG Fan. Central composite design for preparation of Al-based, high specific surface area porous carbon materials derived from walnut green peel[J]. Chinese Journal of Environmental Engineering, 2018, 12(6): 1819-1824. doi: 10.12030/j.cjee.201711177

Citation:

LIU Xiaohong, LI Tiantian, SUN Yuechen, ZHANG Fan. Central composite design for preparation of Al-based, high specific surface area porous carbon materials derived from walnut green peel[J]. Chinese Journal of Environmental Engineering, 2018, 12(6): 1819-1824. doi: 10.12030/j.cjee.201711177

中心组合设计制备高比表面铝基核桃果皮多孔碳材料

1.
延安大学化学与化工学院，延安市分析技术与检测重点实验室，延安 716000
2.
北京工商大学计算机与信息工程学院，北京 100048
基金项目:
国家自然科学基金资助项目（21377107）

2016年陕西省大学生创新创业训练计划项目（1540）

Central composite design for preparation of Al-based, high specific surface area porous carbon materials derived from walnut green peel

1.
Yan’an Key Laboratory of Analytical Technology and Detection, School of Chemistry & Chemical Engineering, Yan′an University, Yan’an 716000, China
2.
School of Computer and Information Engineering, Beijing Technology and Business University, Beijing 100048, China
Fund Project:

摘要: 以农业废弃物核桃青果皮为原料、F127为微结构调控剂、硝酸铝为中心配位离子，通过中心组合设计，螯合辅助共组装策略制备了系列铝基多孔碳材料并对制备参数进行优化分析。选择硝酸铝浓度、铝基复合材料与F127的质量比和碳化温度作为优化因素，研究各因素的不同水平对系列碳材料比表面积的影响。得到制备的最优条件为硝酸铝浓度1 mol·L-1，铝基复合材料与F127质量比为2.5及碳化温度850 °C。在此条件下，制备得到的碳样品的比表面积为1 505.86 m2·g-1，与预测值1 503.77 m2·g-1接近，说明与响应方程模型高度拟合。
- 中心组合设计 /
- 铝基 /
- 高比表面积 /
- 多孔碳
Abstract: In a chelate assisted, co-assembled strategy, Al-based composites were fabricated by using walnut green peel as precursor, which was deemed to be an agricultural waste. Al3+ as the center ion, pluronic F127 as a pore regulator, then a series of porous carbon materials were prepared according to central composite design. Response surface method (RSM) was used to optimize the preparation parameters. In RSM analysis, the interactive effects of aluminum nitrate concentration, the mass ratio of Al-based composites to F127 and carbonated temperature on the specific surface area of porous carbon samples were investigated. The results showed that the optimal values of above parameters were determined as follows: aluminum nitrate concentration (1 mol·L-1), the mass ratio value of Al-based composites to F127 (2.5), and carbonated temperature (850 °C). Under the optimized conditions, the experimental value of specific surface area of porous carbon sample was 1 505.86 m2·g-1 and was in good agreement with the predicted value 1 503.77 m2·g-1, which demonstrated that this method is feasible.
- central composite design /
- Al-based /
- high specific surface area /
- porous carbon

[1]	刘丹, 胡艳艳, 曾超, 等. 有序介孔碳材料的软模板合成、结构改性与功能化[J]. 物理化学学报,2016,32(12):2826-2840 10.3866/pku.whxb201609141
[2]	张继义, 梁丽萍, 蒲丽君, 等. 小麦秸秆对Cr(Ⅵ)的吸附特性及动力学、热力学分析[J]. 环境科学研究,2010,23(12):1546-1552
[3]	周岩梅, 张琼, 刁晓华, 等.硝基苯和西维因在活性炭上的吸附效果及动力学研究[J]. 中国环境科学,2010,30(9):1177-1182
[4]	DEMIRBAS A.Agricultural based activated carbons for the removal of dyes from aqueous solutions: A review[J].Journal of Hazardous Materials,2009,167(1):1-9 10.1016/j.jhazmat.200812114
[5]	甘琦, 周昕, 赵斌元, 等. 成型活性炭的制备研究进展[J]. 材料导报,2006,20(1):1-63 10.3321/j.issn:1005-023X.2006.01.016
[6]	王秀芳, 张会平, 肖新颜, 等. 高比表面积活性炭研制进展[J]. 功能材料,2005,36(7):975-977 10.3321/j.issn:1001-9731.2005.07.002
[7]	FECHLER N, FELLINGER T P, ANTONIETTI M. “Salt templating”: A simple and sustainable pathway toward highly porous functional carbons from ionic liquids [J].Advanced Materials,2013,25(1):75-79 10.1002/adma.201203422
[8]	LEE J, KIM J, HYEON T.Recent progress in the synthesis of porous carbon materials [J].Advanced Materials,2006,18(16):2073-2094 10.1002/adma.200501576
[9]	LIANG C, HONG K, GUIOCHON G A, et al.Synthesis of a large-scale highly ordered porous carbon film by self-assembly of block copolymers [J].Angewandte Chemie,2004,43:5785-5789 10.1002/anie.200461051
[10]	WANG Z Y, KIESEL E R, STEIN A.Silica-free syntheses of hierarchically ordered macroporous polymer and carbon monoliths with controllable mesoporosity [J].Journal of Materials Chemistry,2008,18(19):2194-2200 10.1039/B719489G
[11]	HUANG Y, CAI H, FENG D, et al.One-step hydrothermal synthesis of ordered mesostructured carbonaceous monoliths with hierarchical porosities [J].Chemical Communications,2008,23:2641-2643 10.1039/B804716B
[12]	CHOW S C.Encyclopedia of Biopharmaceutical Statistics[M].New York: Marcel Dekker,2000:500-503
[13]	陈魁. 试验设计与分析[M]. 北京: 清华大学出版社,1996
[14]	逯家辉, 姜鑫, 李昊龙, 等. 应用响应面法优化超声波法提取甘草中总黄酮的工艺[J]. 吉林大学学报（工学版）,2008,38(sup.2):293-298
[15]	蒋莉, 马飞, 梁国斌, 等. 木质素活性炭的制备及工艺优化[J]. 新型炭材料,2011,26(5):396-400

点击查看大图

计量

文章访问数: 2247
HTML全文浏览数: 1949
PDF下载数: 381
施引文献: 0

中心组合设计制备高比表面铝基核桃果皮多孔碳材料

1. 延安大学化学与化工学院，延安市分析技术与检测重点实验室，延安 716000
2. 北京工商大学计算机与信息工程学院，北京 100048

基金项目:

国家自然科学基金资助项目（21377107）

2016年陕西省大学生创新创业训练计划项目（1540）

关键词:

摘要: 以农业废弃物核桃青果皮为原料、F127为微结构调控剂、硝酸铝为中心配位离子，通过中心组合设计，螯合辅助共组装策略制备了系列铝基多孔碳材料并对制备参数进行优化分析。选择硝酸铝浓度、铝基复合材料与F127的质量比和碳化温度作为优化因素，研究各因素的不同水平对系列碳材料比表面积的影响。得到制备的最优条件为硝酸铝浓度1 mol·L-1，铝基复合材料与F127质量比为2.5及碳化温度850 °C。在此条件下，制备得到的碳样品的比表面积为1 505.86 m2·g-1，与预测值1 503.77 m2·g-1接近，说明与响应方程模型高度拟合。

English Abstract

Central composite design for preparation of Al-based, high specific surface area porous carbon materials derived from walnut green peel

1. Yan’an Key Laboratory of Analytical Technology and Detection, School of Chemistry & Chemical Engineering, Yan′an University, Yan’an 716000, China
2. School of Computer and Information Engineering, Beijing Technology and Business University, Beijing 100048, China

Fund Project:

Keywords:

Abstract: In a chelate assisted, co-assembled strategy, Al-based composites were fabricated by using walnut green peel as precursor, which was deemed to be an agricultural waste. Al3+ as the center ion, pluronic F127 as a pore regulator, then a series of porous carbon materials were prepared according to central composite design. Response surface method (RSM) was used to optimize the preparation parameters. In RSM analysis, the interactive effects of aluminum nitrate concentration, the mass ratio of Al-based composites to F127 and carbonated temperature on the specific surface area of porous carbon samples were investigated. The results showed that the optimal values of above parameters were determined as follows: aluminum nitrate concentration (1 mol·L-1), the mass ratio value of Al-based composites to F127 (2.5), and carbonated temperature (850 °C). Under the optimized conditions, the experimental value of specific surface area of porous carbon sample was 1 505.86 m2·g-1 and was in good agreement with the predicted value 1 503.77 m2·g-1, which demonstrated that this method is feasible.

全文HTML

参考文献 (15)

下载: 全尺寸图片幻灯片

返回文章

用微信扫码二维码

分享至好友和朋友圈

中心组合设计制备高比表面铝基核桃果皮多孔碳材料

Central composite design for preparation of Al-based, high specific surface area porous carbon materials derived from walnut green peel

计量

出版历程

中心组合设计制备高比表面铝基核桃果皮多孔碳材料

English Abstract

Central composite design for preparation of Al-based, high specific surface area porous carbon materials derived from walnut green peel

全文HTML

目录